涩老板在线免费视频_午夜成人精品_神马理论午夜,,_亚洲有薄码区久久欧美精品一区_97人人色_神马在线精品_成人熟女一区二区_亚洲二区三区四区_人妻午夜免费_大鸡巴猛男爆操骚逼国产一区二区_丁香婷婷久久一区二区三区_岛国内射美女_亚洲一级电影,亚洲欧美日韩国产最新版,亚洲五月综合缴情综合久久本,少妇色情喷水又紧又爽小说,巜上司的少妇的滋味,国产精品三级女人国产香蕉,亚洲最好的免费电影,欧美亚洲国产成人精品,国产永久一区二区三区,亚洲综合一区无码精品,歳の熟女セックス,内射带小孩熟妇,果冻传媒在线看免费视频观看,成人欧美一区二区三区片,亚洲 片内射欧美美妇,一本无码人妻在中文字幕免费,亚洲无毛视频,中文字幕丰满孑伦无码专区,亚洲爆乳无码专区色戒纶理,肉乳床欢无码片动漫软件,欧美日韩一区二区另类,久热只有精品在线直播,精品亚洲一区二区在线播放,精品国产乱码久久久久久影片,国产一级高清在线观看,国产精品福利在线一区,成人动漫下载,乱伦性爱视频,xo无码AV毛,国产黄A片免费网站免费,日韩欧美一级特黄特色大片

山東通風管道加工的過程中應該盡量避免出現縱向接縫，但是不能出現橫向接縫。而且通風管道的咬口縫和四角的縫隙處，需要按照設計潔凈等級要求，然后還要采用密封膠將其堵嚴。使室內空氣滿足衛生要求和生產過程需要。建筑中完成通風工作的各項設施，統稱通風裝置。

During the processing of Shandong ventilation pipes, longitudinal joints should be avoided as much as possible, but transverse joints should not occur. In addition, the seam of the ventilation pipe and the joints at the four corners need to be sealed tightly with sealant according to the design cleanliness level requirements. Ensure that indoor air meets hygienic requirements and production process needs. The various facilities that complete the ventilation work in a building are collectively referred to as ventilation devices.

一、通風工程的排風口裝置：

1、 Exhaust device for ventilation engineering:

衛生間排風口應盡量裝置在馬桶之上。其它由主機連出的排風管路應盡量短直，咱們主張管路不出衛生間，這樣可以使新風與排風充沛混合后置換循環排出，防止通風死角。排風口分側排、直排兩種形式，排風口裝置要牢固，風口緊貼墻面或吊頂。

Toilet exhaust outlets should be installed above the toilet as much as possible. Other exhaust pipes connected from the main engine should be as short and straight as possible. We advocate that the pipes should not go out of the bathroom, so that fresh air and exhaust air can be fully mixed and replaced for circulation and exhaust, preventing ventilation dead spots. The air outlet is divided into two types: side exhaust and direct exhaust. The air outlet device should be firm, and the air outlet should be close to the wall or ceiling.

二、通風工程進風器的裝置：

2、 Installation of air intakes for ventilation works:

進風器方位一般主張挑選在住宅的窗戶下方（間隔地上不小于50cm）、暖氣上方處等處，便利裝置與保護，并且不影響室內物品的擺放，要盡量防止死角，較好的方式是進風器與排風口成對角線使新風與室內污濁空氣構成對流循環，防止室內空氣出現通風死角。

The orientation of the air inlet is generally recommended to be selected below the windows of the residence (with a spacing of not less than 50cm above the ground), above the heating, etc., to facilitate installation and protection, and not affect the placement of indoor items. It is necessary to prevent dead corners as much as possible. A better way is to diagonally align the air inlet and exhaust outlet to form a convective circulation between fresh air and indoor dirty air, to prevent the occurrence of ventilation dead corners in the indoor air.

進風器的裝置要牢固，室外防雨部分可運用自攻絲與防水玻璃膠（特殊情況可運用防水泡沫膠）進行固定，但方向不行歪斜避免影響防雨作用。室內部分可運用中性玻璃膠或自攻絲進行固定，風口里外部分都應緊貼墻面。

The device of the air inlet should be firm. The outdoor rain proof part can be fixed with self tapping and waterproof glass glue (waterproof foam glue can be used in special cases), but the direction should not be skewed to avoid affecting the rain proof effect. The indoor part can be fixed using neutral glass adhesive or self-tapping, and the inner and outer parts of the air outlet should be tightly attached to the wall.

通風管道加工系統就是實現通風這一功能，包括進風口、排風口、送風管道、風機、降溫及采暖、過濾器、控制系統以及其他附屬設備在內的一整套裝置。以上就是為您講解的部分內容，您還有什么事項就來咨詢我們http://m.okok0579.com吧！

The ventilation pipe processing system is a complete set of devices that achieve the function of ventilation, including air inlets, exhaust outlets, air supply pipes, fans, cooling and heating, filters, control systems, and other auxiliary equipment. The above is part of the content explained for you. If you have any further matters, please come to consult us http://m.okok0579.com Come on!